| Woertz's Cabling systems |
| |
| Our cabling systems may be
divided into two groups according to their field of application:
|
| Systems for building
installation |
| Suitable systems: |
| |
ecobus power 5x10 mm˛
In buildings, this system acts as an "Energy Bus" and is ideal
to perform a ring circuit for example to supply an entire
building floor. The system can thus be compared to a flexible
conductor rail. Outlets are intended for conductors of 4 mm˛
section. In order to fully enjoy the flexibility of such
an installation, we also recommend to use the ecobus power
system together with decentral organized safety cutouts. In a
further step, to connect the end-receivers while keeping the
advantages of the flat cable installation up to the devices,
both systems ecobus combi and ecobus power 5x2.5 with 2.5 mm˛
section can be used (see below). |
| |
ecobus combi 5x2,5 mm˛ + 2x1,5 mm˛
The system for building automation. Both power current
lines 5x2,5 mm˛ and bus lines 2x1,5 mm˛ with twin shielding are
combined in one sheath. This means that the bus lines must not
be interrupted any more for connecting devices - a principle,
that was only used for power current lines until now. Thanks to
ecobus combi, the bus installation requires a minimum of wiring
works. Due to the decentralized repartition of the bus devices,
the structure of the installation suits perfectly every type of
requirements.
|
| |
ecobus power 5x2,5 mm˛
Combined with the ecobus power 5x10 system
mentioned above or used as a system of its own - ecobus power
5x2.5 proved to be ideal for performing a flexible connection of
end receivers. Even if bus control is not foreseen in every
building, the implementation should take a future bus
installation into account. Thanks to ecobus power 5x2.5 this can
easily be achieved. |
| |
ecobus data 2x1.5 mm˛
This cable is a signal line, which can be laid in the
building without being interrupted anywhere. It has interesting
properties in the field of data transmission and has specially
been conceived for bus systems in building automation such as
KNX/EIB and similar systems. The twisted pair is replaced by a
twin shielding which fully protects the conductors and ensures
the secure working of the bus installation. ecobus data is
intended for the connection of sensors. For actuators it is
recommended to use the ecobus combi cable which can
simultaneously supply the devices with current.
|
| |
multibus 4x1,5 mm˛
The ideal complement of ecobus combi.
Multibus has been conceived for wiring bus systems or other
control devices which need three or four untwisted leads. The
basic version of the cable meets the requirements of protection
degree IP 42. Higher protection degrees are available on
request. The multibus system allows a simultaneous connection of
the different leads. Thanks to a special swiveling mechanism
fitted with pointed contacts, contact can quickly be established
both whenn connecting the outlets and when mounting the
connecting box on the cable. |
| |
ecoline-p3 3x2,5 mm˛
The new quick connection technique: the contact is established
simultaneously with the 3 leads without any tool. This cabling
technique is based on a completely new connection principle
which is the result of our 30 years' experience in this field.
When folding back the integrated lever the flat cable is
connected by means of sheath piercing cutting teeth. Ecoline-p3
is specially designed for lamp connection or socket cabling.
|
| Systems for industrial
application |
| Suitable systems: |
| |
ecofil i 5x16 mm˛
Thanks to this system, installing
industrial appliances can quickly be performed saving both work
and time. Compared to a conventional, rigid current rail it has
all the advantages of a flexible flat cable. The connecting
boxes show a protection degree of IP 65 which suit industrial
applications. They are fitted with compact terminal blocks which
are easy to manipulate. If necessary safety cutouts can be
connected to the boxes either directly at the output or
separately by means of a cable.
|
| |
ecofil i 7x2,5 mm˛
Industrial appliances nowadays reach a
high flexibility thanks to bus systems and control devices. To
allow easy implementation and maintenance works, the applicances
often have a modular structure which has already been determined
during planning. The ecofil i 7x2.5 system perfectly suits
appliances which have to be easy to modify and where power
current and weak current have to be supplied in an easy and
secure way. Thanks to this system, the T-pieces which are
commonly liable to breakdowns and which are usually necessary
for the branching of round cables can be avoided.
|
| |
|
Should you require further information, advice or
technical details on our cabling systems, please refer to our
special site:
www.smart-installation.com |
